NAME

DESCRIPTION

The National Instruments models 6601 and 6602 PCI counter/timers provide four and eight 32-bit counter channels respectively. The 6601 specifies a maximum unprescaled count rate of 20 MHz while the 6602 specifies 80 MHz. However, all inputs may be prescaled by a factor of eight, extending the usable maximum count rates to 60 MHz for the 6601 and 125 MHz for the 6602. (The prescaling also gives three more bits of effective counter size.)

When counting to time, for shorter count times, spec uses the 20 MHz built-in clock. If prescale is on for the time channel (which it is by default), the effective clock rate is 2.5 MHz. With a 32-bit counter, that allows for a maximum count time of just under 28.6 minutes (1717.9 seconds). If prescale is off, the maximum count time is 214.7 seconds (3.6 minutes). For longer count times, spec uses the 100 KHz clock with prescaling off, allowing for a maximum count time of nearly 12 hours (as of spec release 5.06.05-3).

spec will keep track of overflows to the channel counting time (when not counting to a time preset), but does not currently correct for counter overflows in the other channels.

spec also provides commands for selecting the hardware's digital debouncing filter for external inputs and for accessing the eight digital I/O pins available on these cards. See the FUNCTIONS section below for details.

SOFTWARE CONFIGURATION

Use spec's configuration editor (edconf, normally invoked by the config macro) to select the timer and to configure the scaler channels. On the Devices screen, you need only enter the the number of counters to be used on the board. The base address of the PCI cards is determined automatically.

SCALERS  DEV  ADDR  <>MODE  NUM                             <>TYPE
    YES                       4  NI PCI 6601/6602 as Counter/Timer
    YES                       8       NI PCI 6601/6602 as Counters


On the Scaler screen, choose NI660x as the device type. The unit numbers are assigned consecutively to the NI PCI counter/timers according to the order they are listed on the Devices screen, starting with unit zero.

NUMBER      NAME  MNEMONIC  <>DEVICE  UNIT  CHAN   <>USE AS  SCALE
     0   Seconds       sec    NI660x     0     0   timebase      1
     1   Monitor       mon    NI660x     0     1    monitor      1
     2  Detector       det    NI660x     0     2    counter      1
     3 Counter 2        c2    NI660x     0     3    counter      1
     3 Counter 3        c3    NI660x     1     0    counter      1
     3 Counter 4        c4    NI660x     1     1    counter      1


The scale factor is ignored for the time-base channel, since the time base is set and accounted for internally in the C code.

THEORY OF OPERATION

One of the key requirements for counter/timers in spec is the capability to have a master channel that will gate the slave counter channels by way of a hardware signal. A second requirement is that at least two channels (one for time and one for monitor) can be used as the master channel. Even better is hardware that allows any channel to be used as the master channel. The NI 6601 and 6602 meet these requirements.

The 660x card architecture allows any channel to be configured to use any other channel's associated gate input pin as its own gate. spec requires each possible master counter's output connected to its associated gate via a jumper. That counter's output will then serve as gate for all the counters. See the Hardware Configuration section below.

Normally all outputs are disabled. When a particular counter is the master, spec configures just that channel to have its output activated during counting to serve as gate for all channels. When the master counter counts down from its preset and reaches zero, the last count changes the state of the output, which disables the slave counters. This achieves a reliable hardware gating.

If the card is set up as only counters, spec configures the card so that all channels will gate off the gate pin associated with the lowest numbered channel included in the config file. The external gate from the master timer device can be connected to that pin.

If the 660x is to be used as master to gate other cards, one must connect the various designated output pins of the possible master counter channels together and use that signal. spec will only activate one output pin at a time. All the other pins will be in the default power-on state of high-impedance inputs, so there is no danger of overloading the outputs as long as spec is used to control the card.

By default, spec programs each channel for an active-high gate. That is, during counting the output signal from the master channel will be nominally at +5V. The counter_par() command can be used to configure the gate signal as active low (see below), if that makes gating other devices more convenient. Note, the gate mode is reset to the default after reading the hardware config file. If using active-low gates, add the appropriate command for setting active- low gates to a config_mac macro, which will be called automatically during hardware configuration.

Although hardware gating is preferred for counters, spec does in any case send appropriate commands to arm and disarm the counters in the absence of hardware gating. The arm command occurs before the master timer is started. The disarm command occurs after the master timer has stopped. If no hardware gate is used with NI PCI cards configured as just counters, the active-low gating mode needs to be set, otherwise the counters will stay inhibited.

HARDWARE CONFIGURATION

For each counter channel that will be used as a master timing channel (either with the internal time base or with an external monitor-count preset), you need to connect the associated output pin to the associated gate pin. It doesn't hurt to make all the connections, even if you don't anticipate the channel being used for a monitor preset channel. All models can have the following connections:

Out(0) pin  5 to Gate(0) pin  3
Out(1) pin  9 to Gate(1) pin  8
Out(2) pin 32 to Gate(2) pin 67
Out(3) pin 29 to Gate(3) pin 64

Out(4) pin 26 to Gate(4) pin 61
Out(5) pin 23 to Gate(5) pin 58
Out(6) pin 53 to Gate(6) pin 21
Out(7) pin 16 to Gate(7) pin 51

Input signals connect to the following pins. Note, one channel will probably be used for the time base, as selected in the config file. There's no need to connect an input signal to that channel, since it will be programmed to use the internal clock.

Source(0) pin  2
Source(1) pin  7
Source(2) pin 34
Source(3) pin 31

Source(4) pin 28
Source(5) pin 25
Source(6) pin 22
Source(7) pin 52

FUNCTIONS

The following counter_par() options are available. The first two commands are associated with particular counter channels:

counter_par(mne, "monitor")

Sets the channel assigned to mnemonic mne to be the monitor preset channel. The monitor channel gets reset when the config file is read on start up or on reconfig.

counter_par(mne, "prescale" [, how])

Without the optional argument, returns nonzero if the channel for mne has been configured with the divide-by- eight prescale. If called with how nonzero, turns on the divide-by-eight prescale. Rereading the config file resets the mode to the default, which is prescale on for the time-base channel, and prescale off for the rest.

counter_par(mne, "filter" [, val])

Without the optional argument, returns zero, 1e-6, 5e-6, 1e-7 or 5e-7 indicating which digital debouncing filter is associated with the input signal for the corresponding counter channel. The units are seconds. Otherwise, sets the filter according to val. A parameter of zero disables the filter. The code also accepts 1, 5, 100 or 500 as valid arguments. According to the NI documentation, input pulses with widths equal to or greater than the value indicated are guaranteed to be passed, and pulses with widths of half the value or less are guaranteed to be blocked. This parameter can also be set in the config file as optional scaler parameter "misc_par_1". (Type s from the main Scaler screen to access the optional parameters.) (Filter support added in spec release 5.07.03-1.)

The following options are associated with the operation of the card, not with a particular channel. The mne argument is necessary for the syntax of the command and should be the mnemonic or counter number of any of the configured channels associated with the card.

counter_par(mne, "active_low" [, how])

Without the optional argument, returns nonzero if the counting card associated with channel mne has been configured for active- low gates. If called with how nonzero, turns on the active-low mode for gating. Otherwise, sets the default active-high gate mode. Rereading the config file resets the mode to active high. The mode only needs to be set for one channel to affect all channels on the card.

counter_par(mne, "io_config" [, val])

Bits set in val will be configured as outputs on the digital I/O lines. On power up, all lines are configured as inputs. If the optional argument is missing, spec will return the current value as set by the user. (The value can't be read from the card itself.)

counter_par(mne, "set_bit", val)

Set output lines corresponding to bit number val to high, where bits and lines are numbered from 0 to 7.

counter_par(mne, "clr_bit", val)

Set output line corresponding to bit number val to low, where bits and lines are numbered from 0 to 7.

counter_par(mne, "put_byte", val)

Sets output lines corresponding to the bits set in val to high and bits not set in val to low.

counter_par(mne, "get_bit", val)

Returns 0 or 1 based on whether the input line corresponding to bit number val is high or low, where lines and bits are numbered from 0 to 7.

counter_par(mne, "get_byte")

Returns an 8-bit value that reflects the setting of the input lines.