NAME

BUILT-IN FUNCTIONS

gpib_cntl(a, s)

Performs the selected GPIB command on the device with address a. The string s is one of the following:

"gtl"

Go to local.

"llo"

Local lockout.

"sdc"

Selected device clear.

"dcl"

Device clear (sent to all devices).

"get"

Group execute trigger (only sent to the single addressed device).

"ifc"

Interface clear. This command resets the GPIB bus by sending the IFC message. The address a is ignored. spec runs the same code sequence with the "ifc" command as it does when it initializes the GPIB controller on start up or on the reconfig command. For most controllers, spec sleeps for some fraction of a second after resetting the bus. Also, for most controllers, spec asserts the REN (remote enable) command after sending IFC.

gpib_get(a)

Returns a string from the GPIB device with address a. Requires the device to terminate the string with a newline, although the trailing newline (and carriage return, if present) is removed from the string before it is returned.

gpib_get(a, n)

As above, but reads n bytes and doesn't look for a terminator.

gpib_get(a, eos)

As above, but reads up until a terminator given by the first character of the string eos, except for the special cases described below. The terminator is removed.

gpib_get(a, d)

Reads incoming bytes into the data array d. The size of d determines how many bytes are to be read. Sub-array syntax can be used to limit the number of bytes. The function returns the number of array elements read, or zero if the read times out. Note, no byte re-ordering is done for short- or-long integer data, and no format conversions are done for float or double data.

gpib_get(a, mode)

If mode is the string "byte", reads and returns one unsigned binary byte. If mode is the string "short", reads two binary bytes and returns the short integer so formed. If mode is the string "long", reads four binary bytes and returns the long integer so formed. The last two modes work the same on both big-endian and little-endian platforms. On both, the incoming data is treated as big endian. If the incoming data is little endian, use "short_swap" or "long_swap". (For spec versions prior to release 5.01.01, use int2 for short and int4 for long.)

gpib_poll(a)

Returns the serial-poll status from the device with address a.

gpib_put(a, s)

Writes the string s to the GPIB device with address a. Returns the number of bytes written.

gpib_put(a, d, [cnt])

Writes the contents of the data array d to the GPIB device with address a. By default, the entire array (or subarray, if specified) will be sent. The optional third argument cnt can be used to specify the number of array elements to send. For short and long integer arrays, the data will be sent using native byte order. The "swap" option of the array_op() function can be used to change the byte order, if necessary. No format conversions are available for float or double data. Returns the number of bytes written.

gpib_put(a, "")

Performs a listener check at device address a. Writing a null string (zero-length message) generates a return value of 1 if there is a listener, zero if there is no listener and -1 if the GPIB controller doesn't support the test (as of spec release 5.07.03-4).

MULTIPLE GPIB CONTROLLERS

spec allows up to eight GPIB controllers to be configured by the same instance of spec. In the configuration editor, use the ^F and ^B command on the GPIB controller line of the Interfaces screen to configure each controller. To include a unit number in a GPIB address for a device, enter the address using the notation unit:address. An absent unit: prefix implies GPIB controller unit zero.

In the config file, the unit number associated with a GPIB controller is specified with @gpib_0, @gpib_1, etc. Also, GPIB unit numbers are encoded using

unit x 100 + address.


SECONDARY GPIB ADDRESS

Secondary GPIB addresses are supported for all the above functions. The address argument must be passed as a string however, of the form "pri_sec", where pri is the primary GPIB address and sec is the secondary GPIB address. For example,

print gpib_get("3_12")


SHARING GPIB CONTROLLERS

spec communicates with the GPIB controllers at board (rather than device) level. That makes it unlikely that an arbitrary program could also use the same GPIB controller successfully simultaneously. However, spec can share a GPIB controller among multiple instances of itself. The state of the controller is communicated between the processes using the interprocess communications (IPC) semaphore and shared- memory facilities. Thus sharing is only available on platforms that include these facilities in the kernel.

When sharing multiple GPIB controllers, please note it is essential each shared controller have the same GPIB controller unit number in the spec configuration file.

Note that spec uses only one semaphore to regulate access to all the shared controllers. Thus, if there are two GPIB controllers configured as shared, when any process accesses either controller, other processes will be blocked from accessing both controllers until the first process releases the semaphore. Note also that when the Kinetic Systems KS-3929 SCSI- to-CAMAC controller is configured as a shared controller, the same semaphore is again used.

SEE ALSO